Welcome to Rick's CustomPro Roofing Company - Arlington, TX - Serving DFW
Fully Insured - 20+ Yrs Experience in Arlington - Commercial and Residential Roofing - Locally Owned - Same Day Service
 free quotes in Arlington on all roofing - commercial and residential
|
|
Rick's Commercial Roofing of Arlington, TX handles all roofing projects in DFW and North Texas
This site will be a live roofing company site soon, specializing in flat roofing in DFW. In the meantime, please visit 360 Innovations Roofing's homepage for all of your roofing needs. Serving Dallas for over 20 years with reliable roofing craftsmanship. In the future we will spotlight other great companies but for now, check them out.
Common Roofing Material Questions and Answers | Valley and Eaves Flashing
Valley can be protected with galvanized metal or with a mineral surface product such as EZ Roof, made by Tarmac Roofing Systems, roll roofing, or a rubberized polyethylene, self-adhering membrane. To estimate the amount of metal valley material needed, measure the length of the valley around the roof's surface. If you cannot obtain the metal in one continuous roll, add 6 inches for each overlap and add another 8 inches for overlap at the ridge and eaves. Use the same procedure for estimating mineral-surface roll roofing. If you use roll roofing for valley flashing, double the amount of the measured length. Two layers of roll roofing are needed for adequate protection against leaks in valleys. Metal and mineral-surface roll roofing used for valleys should be at least 36 inches wide.
Roofing Cement - a variety of asphalt coatings, adhesives, and cements is available for roofing. In a recent project at Malarkey's Irish Pub of Dallas, we used asphalt/plastic based cement, which is the most frequently used product for waterproofing around chimneys, vents, and skylights. A gallon or two of roofing cement should be more than adequate for the typical 20-square home. Use roofing cement that specifies a plastic base or a rubberized compound. As an alternative to messy-to-use roof cement, the 3M company has developed a sealer that can be pressed into place. This caulk-like product comes in 15 foot wide solid tape and is guaranteed for 20 years against cracking and peeling. We have also performed work for NEADL and US Tree Service of Carrollton Texas. While we no longer service the Richardson, TX area, our buddies at 360 Innovations Roofing Company can help east of Dallas.
As a general rule, if you cannot obtain precut aluminum step flashing in the proper cut, you can always cut and bend each pieces in half to make them 7x5 inches. Allow for a 2-inch overlap of each piece when you are measuring for step flashing that is to be installed along a wall or chimney.
For a re-roofing job, carefully remove and reuse all pipe collars. If the collars and shingles were properly installed, the old shingles will have protected the collars from wear. For new work, measure the circumferences of the pipes and purchase either metal or polyurethane collars.
Hosting by AdamsDR | Some content courtesy of BKR Pros |
Rick's CustomPro Commercial Roofing Company
Serving Arlington, Texas | Your Local Arlington Roofing Experts
At Rick's CustomPro Roofing Company, we understand that your roof is the most critical line of defense for your property. Serving both residential and commercial clients in Arlington, Texas, we specialize in high-quality installations designed to withstand the unique challenges of the North Texas climate—from scorching summer heat to unpredictable hail storms.
How a Roofing System Works
A roof is far more than just shingles. It is a complex system of integrated components working together:
Roof Decking: The structural foundation (usually plywood or OSB) that supports the weight of the system.
Ice and Water Shield: A waterproof membrane applied to vulnerable areas like valleys and eaves to prevent leaks.
Underlayment: A secondary water-resistant layer (synthetic or felt) that sits between the decking and the shingles.
Flashing: Metal pieces installed around chimneys, vents, and walls to redirect water away from joints.
Shingles/Covering: The outermost layer (asphalt, metal, or TPO for commercial) that provides the primary weather barrier.
Ventilation: Intake and exhaust vents that allow the attic to breathe, preventing heat and moisture buildup.
Key Benefits of Roof Replacement
Investing in a new roof offers significant long-term value for home and business owners:
Enhanced Safety: Modern materials offer superior fire ratings and wind resistance (up to 130 mph).
Improved Energy Efficiency: Reflective shingles and proper insulation reduce attic temperatures, lowering AC costs in the Texas summer.
Increased Property Value: A new roof provides one of the highest Returns on Investment (ROI) for property resale.
Curb Appeal: Modern architectural shingles or sleek metal roofing instantly modernize the look of your building.
Warranty Protection: New systems come with manufacturing and workmanship warranties, providing peace of mind for decades.
Why Arlington Properties Need Custom Work
Arlington sits in the heart of 'Hail Alley.' We don't just 'slap on shingles.' We customize every project with reinforced materials and specialized flashing techniques to ensure your property remains dry and secure through every season.
Roofing Cement - a variety of asphalt coatings, adhesives, and cements is available for roofing. In a recent project at Malarkey's Irish Pub of Dallas, we used asphalt/plastic based cement, which is the most frequently used product for waterproofing around chimneys, vents, and skylights. A gallon or two of roofing cement should be more than adequate for the typical 20-square home. Use roofing cement that specifies a plastic base or a rubberized compound. As an alternative to messy-to-use roof cement, the 3M company has developed a sealer that can be pressed into place. This caulk-like product comes in 15 foot wide solid tape and is guaranteed for 20 years against cracking and peeling. We have also performed work for NEADL and US Tree Service of Carrollton Texas. While we no longer service the Richardson, TX area, our buddies at 360 Innovations Roofing Company can help east of Dallas.
As a general rule, if you cannot obtain precut aluminum step flashing in the proper cut, you can always cut and bend each pieces in half to make them 7x5 inches. Allow for a 2-inch overlap of each piece when you are measuring for step flashing that is to be installed along a wall or chimney.
For a re-roofing job, carefully remove and reuse all pipe collars. If the collars and shingles were properly installed, the old shingles will have protected the collars from wear. For new work, measure the circumferences of the pipes and purchase either metal or polyurethane collars.
Hosting by AdamsDR | Some content courtesy of BKR Pros |
Rick's CustomPro Commercial Roofing Company
Serving Arlington, Texas | Your Local Arlington Roofing Experts
At Rick's CustomPro Roofing Company, we understand that your roof is the most critical line of defense for your property. Serving both residential and commercial clients in Arlington, Texas, we specialize in high-quality installations designed to withstand the unique challenges of the North Texas climate—from scorching summer heat to unpredictable hail storms.
How a Roofing System Works
A roof is far more than just shingles. It is a complex system of integrated components working together:
Roof Decking: The structural foundation (usually plywood or OSB) that supports the weight of the system.
Ice and Water Shield: A waterproof membrane applied to vulnerable areas like valleys and eaves to prevent leaks.
Underlayment: A secondary water-resistant layer (synthetic or felt) that sits between the decking and the shingles.
Flashing: Metal pieces installed around chimneys, vents, and walls to redirect water away from joints.
Shingles/Covering: The outermost layer (asphalt, metal, or TPO for commercial) that provides the primary weather barrier.
Ventilation: Intake and exhaust vents that allow the attic to breathe, preventing heat and moisture buildup.
Key Benefits of Roof Replacement
Investing in a new roof offers significant long-term value for home and business owners:
Enhanced Safety: Modern materials offer superior fire ratings and wind resistance (up to 130 mph).
Improved Energy Efficiency: Reflective shingles and proper insulation reduce attic temperatures, lowering AC costs in the Texas summer.
Increased Property Value: A new roof provides one of the highest Returns on Investment (ROI) for property resale.
Curb Appeal: Modern architectural shingles or sleek metal roofing instantly modernize the look of your building.
Warranty Protection: New systems come with manufacturing and workmanship warranties, providing peace of mind for decades.
Why Arlington Properties Need Custom Work
Arlington sits in the heart of 'Hail Alley.' We don't just 'slap on shingles.' We customize every project with reinforced materials and specialized flashing techniques to ensure your property remains dry and secure through every season.
Arlington TX Commercial Roofing Explained | A Brief History
The Big Three: TPO, EPDM, and PVC
Choosing the right single-ply membrane is the most critical decision for any flat-roofed commercial building. While they may look similar to the untrained eye, their chemical compositions and performance characteristics vary significantly. 1. TPO (Thermoplastic Polyolefin) Currently the industry leader in market share, TPO is favored for its reflective white surface which can significantly reduce cooling costs. It features heat welded seams, making it remarkably leak-resistant. It's an excellent choice for buildings seeking energy efficiency and a modern aesthetic. 2. EPDM (Ethylene Propylene Diene Terpolymer) Known commonly as "rubber roofing," EPDM has been a staple for decades. It is incredibly durable and holds up well against hail and thermal shock. While traditionally black, it is now available with reflective coatings. Its main advantage is its long-term proven track record in harsh northern climates. 3. PVC (Polyvinyl Chloride) PVC is the high-performance choice. It is naturally resistant to chemicals, oils, and greases, making it the standard for restaurants and manufacturing facilities. Like TPO, its seams are heat-welded, creating a monolithic seal that is stronger than the membrane itself.
SUSTAINABILITY Restoration vs. Replacement: The Power of Roof Coatings In 2026, building owners are looking for ways to extend asset life without the massive capital expenditure of a full tear-off. Enter high-performance silicone and acrylic roof coatings. "A full roof replacement is a capital expense. A roof restoration is often a maintenance expense that can be fully tax-deductible in the year it’s applied." Benefits of Silicone Restoration Systems (SRS): • • • • Leak Elimination: Creates a seamless, waterproof barrier over existing membranes. UV Protection: Reflects up to 88% of solar radiation, lowering building temperatures. Cost Savings: Typically 50-70% less expensive than a full replacement. Environmental Impact: Keeps old roofing materials out of landfills.
TECHNIQUES Modern Installation: Why Induction Welding is Changing the Game The method used to attach a roof is just as important as the material itself. While traditional "screw and plate" methods are still common, induction welding (such as the RhinoBond system) is revolutionizing the industry. How it Works Unlike traditional mechanical fastening where the fastener only secures the bottom layer, induction welding uses a specialized tool to bond the underside of the membrane to a specially coated plate through the membrane itself. This is done without any penetration of the top layer. The Advantages • • • Higher Wind Uplift Ratings: The load is distributed across more points than traditional fastening. Fewer Fasteners: Often requires 25-50% fewer fasteners than traditional methods. No Membrane Penetration: Since the tool welds from the top without a needle, there is no chance of "missed" fasteners causing leaks.
MAINTENANCE Preventative Maintenance: Your 5-Point Spring Inspection Checklist Neglecting a commercial roof is a recipe for disaster. Small issues caught early cost hundreds; ignored issues cost thousands. Every facility manager should check these five areas every spring: • • • • • Drainage and Scuppers: Clear all debris. Standing water (ponding) is the #1 enemy of flat roofs.
Flashings and Terminations: Check the "edges." Most leaks occur where the roof meets a wall or HVAC unit. Seam Integrity: In TPO or EPDM roofs, look for areas where the seams might be "smiling" or lifting. HVAC Damage: Check for dropped tools, loose screws, or puncture marks near service units. Vegetation Growth: If roots are starting to take hold in dirt piles on your roof, they can quickly penetrate the membrane